Fall Protection - Getting High on Safety

Fall Protection – Getting High On Safety

Fall Protection – Getting High On Safety

High-rise and multi-story construction presents hazards not only to employees working at elevation, but also to workers and others at ground level. Falls, falling objects, cranes and suspended loads, welding operations, changing weather conditions, and simultaneous work on multiple levels can all create serious risks.

Before work begins, a competent person should evaluate the work area and planned activities to identify hazards and determine appropriate controls. Employees should understand the hazards associated with their work and the procedures necessary to protect themselves and others.

Fall Protection

Falls remain one of the leading causes of fatalities in construction. Employees exposed to fall hazards must use the fall protection required for the work being performed.

Before beginning elevated work:

  • Identify unprotected sides, edges, floor openings, holes, skylights, and other fall hazards.
  • Install guardrails, covers, personal fall protection systems, or other required protective measures before exposure occurs.
  • Use only approved anchorage points for personal fall protection equipment.
  • Inspect harnesses, lanyards, self-retracting lifelines, connectors, and other fall protection equipment before each use.
  • Remove damaged, defective, or fall-arrested equipment from service as required.
  • Maintain 100% tie-off when required by the applicable fall protection procedure.
  • Never remove or bypass guardrails, covers, warning systems, or other protective measures without authorization.
  • Ensure employees using personal fall arrest systems are trained in their proper inspection, fitting, connection, and use.

Employees should also understand the project’s fall rescue procedures. A worker suspended after a fall must be rescued promptly.

Falling Objects and Work on Multiple Levels

High-rise construction frequently involves employees working above and below one another. Tools, materials, debris, and equipment falling from an upper level can cause serious or fatal injuries.

To control falling-object hazards:

  • Wear required hard hats.
  • Install toeboards, screens, canopies, barricades, or other falling-object protection where necessary.
  • Secure tools and materials when there is a possibility they could fall.
  • Keep materials away from unprotected edges.
  • Never throw materials or debris from an elevated level unless an approved method, such as an enclosed chute, is provided.
  • Barricade areas below overhead work when falling-object exposure cannot otherwise be eliminated.
  • Stay out of barricaded areas and never work beneath suspended loads.

Personal Protective Equipment

Employees must wear PPE appropriate for the hazards of their assigned work. Depending on the task, this may include:

  • Hard hats.
  • Safety glasses or goggles.
  • Face shields.
  • Hearing protection.
  • Work gloves appropriate for the hazard.
  • Safety footwear.
  • High-visibility apparel.
  • Fall protection equipment.
  • Respiratory protection when required.

PPE must be inspected, properly maintained, and used as trained.

Weather and Environmental Conditions

Weather conditions can become especially hazardous when employees are working at elevation. Wind, rain, ice, heat, and cold can affect footing, balance, visibility, equipment operation, and an employee’s ability to safely perform the work.

Employees should:

  • Monitor changing weather conditions.
  • Keep walking and working surfaces as dry and clear as practicable.
  • Wear footwear appropriate for surface conditions.
  • Dress appropriately for heat, cold, wind, and precipitation.
  • Maintain adequate hydration during hot-weather work.
  • Recognize symptoms of heat and cold stress.
  • Secure loose materials that could become airborne.
  • Stop elevated work when wind, lightning, severe weather, or other conditions make the work unsafe.

Never continue elevated work simply to meet a production schedule when environmental conditions make the task unsafe.

Welding and Hot Work

Welding, cutting, and other hot work can expose employees to fire, burns, fumes, ultraviolet and infrared radiation, electrical hazards, and compressed gases.

Employees performing or working near hot work should:

  • Follow the company’s hot-work procedures and permit requirements.
  • Wear appropriate welding and cutting PPE.
  • Protect nearby employees from welding arcs, sparks, slag, and hot material.
  • Maintain adequate ventilation and use respiratory protection when required.
  • Remove or protect combustible materials.
  • Keep appropriate fire-extinguishing equipment readily available.
  • Properly secure and handle compressed-gas cylinders.
  • Maintain required fire watches when necessary.

Cranes and Suspended Loads

Cranes and hoisting equipment are commonly used to move materials between levels. Suspended loads create serious struck-by and caught-between hazards.

Employees must:

  • Stay clear of suspended loads.
  • Never walk or work directly beneath a load.
  • Observe barricades and controlled-access areas.
  • Remain clear of crane swing radiuses and other equipment danger zones.
  • Follow signals and instructions from authorized riggers, signal persons, and equipment operators.
  • Never attempt to guide or stabilize a load unless authorized and using the proper method.
  • Remain alert to crane and material-handling operations occurring above and around the work area.

Hazardous Materials and Respiratory Hazards

Construction, renovation, demolition, welding, grinding, cutting, abrasive blasting, and coating removal may generate hazardous dusts, fumes, or other airborne contaminants.

Employees must follow established procedures for controlling these exposures. Engineering and work-practice controls should be used where required, and respiratory protection must only be used in accordance with the company’s Respiratory Protection Program.

Materials suspected of containing lead, asbestos, silica, or other hazardous substances must be properly evaluated before employees disturb them.

Before You Start

Conditions on a high-rise construction project can change rapidly. Before beginning a task, employees should consider:

  • What could I fall from or through?
  • What work is occurring above and below me?
  • Could tools or materials fall onto someone?
  • Are cranes or mobile equipment operating nearby?
  • Are guardrails, covers, and other protective systems in place?
  • Is my fall protection equipment properly inspected and connected?
  • Could weather conditions affect the work?
  • Are hot work or hazardous materials present?
  • Do I have the correct PPE and equipment?
  • Has anything changed since the work was planned?

If conditions change or an uncontrolled hazard is identified, stop and notify the supervisor before continuing the work.

Remember

Working high above the ground leaves little room for error. Plan the work, protect every exposed edge and opening, control falling objects, stay clear of suspended loads, and never take shortcuts with fall protection.